search shadow

Menu

Articles in this section

See more

Getting Started with Your ES700 Time Recorder Follow

Avatar
Kristina Donaldson
  • Updated

You received your Acroprint Model ES700 Time Recorder and you're ready to get started. Some items, such as the time and date, are preset at the factory. You can check out our factory settings here. You are able to immediately begin using the device after plugging into an outlet, however, we recommend reviewing the other articles in this section and customizing the device to your needs before use.

In this article:

 

Packaging Contents

Unpack the time recorder and check its contents to ensure that the time recorder unit and all accessories below are included. If equipment has been damaged, contact us.

  • ES700 Time Recorder
  • AC Power Cord and Adapter
  • ES700 Manual
  • (2) Keys
  • (1) Factory Installed Ribbon Cassette
  • (2) Wall Mount Brackets with (2) Screws
  • (1) Wall Mount Sheet with (4) Screws and (4) Mollies

 

Before You Start

Open the Unit

Insert the key into the lock on the cover of the unit. Turn the key clockwise to unlock the unit. Remove the cover.

A diagram of the ES700. An arrow rotates clockwise around the key at the top of the unit. An arrow points up to indicate lifting the cover straight up.

 

Remove the Cardboard Insert

When you open the unit for the first time, you must remove the Protective Pad and Cardboard Insert, then Plug the AC Adapter into the back of the unit. The ink ribbon may dislodge. To avoid damage to the printer, press the ribbon cartridge firmly into position after removing the protective pad.

A diagram of the ES700 without the cover. An arrow points away from the front of the device to indicate pulling the cardboard insert straight out. A second arrow points to the top left of the back of the unit, indicating where to insert the AC adapter.

 

Close Unit

Replace the cover. Insert the key into the lock on the cover of the unit. Turn the key counter-clockwise to lock the unit.

A diagram of the ES700 with the cover on. An arrow points counter-clockwise around the key at the top of the unit.

 

Wall Mounting Instructions

The ES700 should be mounted on 1/2 inch drywall using two ST 4x20 screws and fasteners.

  1. Install the supplied wall-mount screws by using the template. Be sure to keep about 6mm (1/4") of the screw head away from the wall. The recommended height from the floor to the bottom of the unit is 45".

    A diagram of the wall mount template against a wall with lines to indicate inserting the two screws at the top of the cutout holes.

  2. Open the unit.
  3. Hang the unit on the wall and install Wall Mount Brackets.

    A diagram of the ES700 with the cover off with lines leading to the bottom two corners closest to the wall, to indicate where to attach the wall mount brackets to the device.

  4. Close the unit.

 

Power the Unit

To power the device, plug the AC power cord into the back of the ES700, then plug the AC adapter into an outlet. If you are experiencing power issues, confirm the power cord is securely plugged in or try an alternate outlet.

 

Print Position

The print position from the card edge is adjustable by pressing and sliding the print position button located on the bottom of the unit. The maximum distance from the edge of the form to print is approximately 1 3/16" (30 mm).

A diagram showing three possible print options. One showing the left alignment, one alignment beginning in the center starting 15mm position, and one to the far right alignment starting at 30 mm.

 

Settings and Control Buttons

Control Buttons

The ES700 has three (3) control buttons enabling you to quickly locate and adjust a variety of settings.

 

Control Button Function

SELECT

 Press SELECT to choose the desired program setting mode. The selected program setting is indicated by the upward pointing arrow on the display. 
CHANGE Press CHANGE to cycle through the options.
SET Press SET to set the option. Press the SET button again to return the Time Recorder to the normal operation mode. 

 

Settings

To enter the program setting mode, make sure the AC cord is plugged into the AC outlet and remove the cover. Next press SELECT once. The recorder will change to the program mode showing the upward pointing arrow on the display positioned under the TIME mark.

 

Things to remember when adjusting the ES700 settings:

  • You must open the unit to make changes to the settings.
  • After performing each procedure on the unit, remember to press SET until the unit returns to normal operation mode.
  • To exit program mode anytime, press SET until the unit returns to normal operation mode.
  • When you are setting a digit or an option on the display, flashing means that it is ready to be changed. You must press SELECT until you reach the desired digit or option. Then press SET to lock the desired value in place.
  • Printing is always disabled while settings are being changed. Once the final SET has been completed in any given operation, printing is enabled.
  • After updating the settings, replace the cover and lock it.

Related articles